Home Products About Blog Contact
中文

Maintenance

Water Well Rig Maintenance: 10 Checks That Prevent Downtime

May 10, 2026 · 9 min read · Updated October 31, 2026

The expensive failure on a drilling site is rarely normal wear. It is unplanned downtime: a burst hose, a blocked filter or a loose pin that stops the whole crew. These ten checks are grouped by daily, weekly, 250-hour and storage intervals.

Every day before work

1. Hydraulic oil level and condition

Check on level ground with cylinders retracted. Dark, milky, gritty or burnt-smelling oil is not solved by topping up. Find the contamination source. Most hydraulic failures start with oil cleanliness.

2. Hoses, fittings and seals

Look for bulges, abrasion, cracks and weeping fittings. A damp fitting is not cosmetic. It can fail completely under pressure.

3. Engine oil, coolant and belts

Low oil, low coolant or a glazed belt becomes a major repair under load and heat. A daily look is cheaper than an engine rebuild.

4. Mast, pins and fasteners

Mast raising, head travel and winch loads work pins and bolts loose. Re-torque to specification. Do not rely on feel with a standard wrench.

5. Emergency stop, shutdown and anti-drop devices

Test once per shift. Safety devices are rarely used, so they must work when needed.

Every week

6. Head gearbox and swing bearing

Check oil level, breather, seals and noise. The head works at low speed and high torque. Low oil or water ingress destroys gears quickly.

7. Winch rope and sheaves

Inspect for broken wires, flattening, corrosion, end termination and sheave groove wear. Replace rope that meets the discard criteria. Do not run it for a few more days.

8. Tracks or tyres and travel system

For tracks: tension, cracked pads, leaking rollers and idlers. For tyres: pressure, uneven wear and cuts. A failed travel system takes away the rig mobility.

Every 250 hours

9. Filters, engine oil and hydraulic oil

Follow the manual, then shorten intervals for dust, heat and continuous duty. When changing filters, check the tank bottom for water and sediment.

10. Electrics, gauges and sensors

Check harness abrasion, loose plugs, alarms and sensor readings. Many “weak hydraulic” complaints are actually a sensor or solenoid circuit fault.

Long-term storage

Early warning signs

SymptomCheck firstDo not
Head weak, oil hotOil level, filters, pump pressure, relief valveWind up pressure blindly
Mast juddersCylinder internal leak, air, pin clearanceKeep operating under load
Winch creeps downBrake, balance valve, ropeHold the rope by hand
Track runs off lineTension, travel motor, valve blockForce it to keep walking
Engine overheatsRadiator, fan, coolant, water pumpOpen the cap immediately

Spare parts strategy

Do not stock every part. Prioritise wear items and parts with high downtime cost: filters, seals, high-pressure hoses, common solenoids, winch rope, rod joints and DTH wear parts. Overseas projects should keep at least one set of critical parts because customs clearance adds time.

Keep records: date, hours, oil tests, replacements, symptoms and fixes. Next time, the record beats memory.

Frequently asked questions

How often should hydraulic oil be changed?

There is no universal interval. Follow the manual and oil analysis. Dust, heat and continuous duty shorten the interval. Milky, contaminated or metal-bearing oil needs investigation, not just topping up.

When must winch rope be replaced?

Replace it for clustered broken wires, a broken strand, severe flattening, kinking, corrosion, measurable diameter loss or any manufacturer discard criterion. Winch rope is a safety item.

What should be done before restarting a stored rig?

Check oils, filters, battery, belts, hoses, rope, track tension and brakes, then run every function unloaded. Do not go straight to full load after long storage.

Related articles

Reviewed by the Julong engineering team

Based on published drilling practice, equipment manuals and field selection experience. Final configuration and price are confirmed in a written proposal.

Get a Quote → WhatsApp

Send us your job details. We will size the rig.

Tell us the hole depth, diameter, ground conditions and site access. We will recommend a model, configuration and written quotation.

New models and exhibitions

One email a month. No ads.

Search WhatsApp Call us Get a Quote