Home Products About Blog Contact
δΈ­ζ–‡

Exploration

Exploration Drilling Rigs: From Mapping to Resource Estimation

April 5, 2026 Β· 10 min read Β· Updated October 31, 2026

Exploration moves from surface observation to underground proof through drilling. It turns the inferences of mapping, geophysics and geochemistry into measurable, assayable core or samples. Rig choice affects core recovery, sample representativeness and cost per metre.

Where drilling sits in the programme

StageTaskRole of drilling
Geological mappingDefine stratigraphy, structure and mineralisationShallow holes test surface interpretation and boundaries
Anomaly follow-upRank geochemical and geophysical targetsSample below surface to see whether the anomaly is bedrock
Fence drillingTest continuity on sectionSystematic core for grade and width
Resource estimationCalculate tonnage and gradeProvide grade, density, thickness and continuity data

Core rig or RC rig

This is the most common fork in exploration selection.

Core drilling

Choose core when the project needs rock structure, alteration, mineralisation relationships and defensible grade. Wireline coring is efficient, and core can be logged, photographed and sampled directly. The Julong JY-600, JY-800 and JY-1000 series cover different depths; JY600Q is a portable hydraulic option for difficult access.

Air-lift reverse circulation

Choose RC for fast penetration through cover, rapid anomaly testing and continuous chip samples. The JLRC500 series drills to 500 m with 105–400 mm diameters. Samples return through dual-wall rods. It is fast, but the sample is chips, not intact core, so logging and grade interpretation demand more care.

Many programmes use both: RC through the cover, core through the mineralised zone. Ask the geologist whether the project needs metres or interpretable core.

Five details that affect core recovery

  1. Tooling: rod, core barrel, core lifter and reamer must match.
  2. Drilling fluid: poor mud erodes core or collapses the hole.
  3. Weight and rotation: hard rock needs higher weight and lower speed; soft rock needs care against bit balling.
  4. Run length: long runs increase core loss and blockage risk.
  5. Logging and storage: order, numbering, boxing and photography. One mistake here and the assay data cannot be matched.

Hole layout is not the rig decision

The rig drills what the geologist designs. Collar, dip, azimuth, depth and spacing are fixed by the programme. Before drilling, confirm:

If ground conditions differ from the design, talk to the geologist. Do not change depth or skip sampling on site without approval.

Data quality beats metres

An exploration programme is judged on traceability, not only metres drilled. Keep for every hole:

These records are checked during resource estimation, due diligence and tenement transactions. Missing records reduce the value of good drilling.

Configuration advice

For poor access and frequent moves, choose portable or modular hydraulic. For depth and quality, choose wireline coring. For thick cover and rapid evaluation, choose RC. Treat rig, pump, generator, tooling and spares as one system, not a host price plus extras.

Frequently asked questions

Is an exploration rig the same as a core rig?

Not exactly. A core rig is one type of exploration rig, designed for core recovery. Exploration also uses RC and DTH rigs for fast sampling or anomaly testing. The target and sample requirement decide.

What is the difference between wireline and conventional coring?

Wireline retrieves the core barrel through the rods on a wire, so the string stays in the hole. It is faster on deep, continuous programmes. Conventional coring requires tripping the rods each run, simpler but slower.

Can RC samples replace core?

Not completely. RC gives chip samples, useful for rapid evaluation and cover penetration. Core shows structure, alteration and mineralisation relationships. Whether RC samples can enter a resource estimate depends on the geology and reporting rules.

Related articles

Reviewed by the Julong engineering team

Based on published drilling practice, equipment manuals and field selection experience. Final configuration and price are confirmed in a written proposal.

Get a Quote β†’ WhatsApp

Send us your job details. We will size the rig.

Tell us the hole depth, diameter, ground conditions and site access. We will recommend a model, configuration and written quotation.

New models and exhibitions

One email a month. No ads.

Search WhatsApp Call us Get a Quote