Geothermal
Geothermal Well Drilling: A Practical Guide to Ground-Source Loops
March 15, 2026 Β· 10 min read Β· Updated October 31, 2026
In a ground-source heat pump project, the borehole is the underground heat exchanger. Unlike a water well, it must deliver stable heat transfer, sealing and borehole stability over years of operation. Drilling is only one step. Layout, loop installation, grouting and sealing decide the result.
Closed loop or open loop
- Closed loop: U-tubes or double U-tubes are installed and the circulation fluid stays inside the pipe. It does not contact groundwater. Sealing and grouting are critical.
- Open loop: groundwater is abstracted and returned. Yield, recharge capacity and water quality are key, along with abstraction permits and discharge rules.
The two systems use different borehole structures, loop materials and grouting. Do not copy a water well design.
Loop layout
More boreholes or deeper holes is not automatically better. The design depends on building heating and cooling load, available land, groundwater flow, existing services and spacing between holes. Holes too close together interfere and reduce long-term performance. Sites near contamination or sensitive groundwater need extra assessment.
The design should state total metres, depth per hole, diameter, spacing, loop specification, grout material, manifold location and pressure test requirements.
Drilling method
| Ground | Method | Watch |
|---|---|---|
| Clay, silt, sand | Mud circulation, casing | Collapse, hole closure, mud properties |
| Gravel, cobbles | Casing while drilling, percussion | Stuck tools, diameter and verticality |
| Bedrock | DTH, roller or diamond | Deviation, loop installation clearance |
Water well, DTH and core rigs can all be used. The requirement is matched diameter, depth, tooling and cuttings removal, with stable hole walls and controlled deviation.
Loop installation and grouting
Before installation, ream and flush the hole. Confirm there are no large fallen blocks or tight sections. Protect the loop from kinking, scoring and debris. Grout is usually bentonite, cement-based or a proprietary mix. Its job is to fill the annulus, improve heat transfer and prevent cross-flow between aquifers.
Incomplete grouting is a common failure:
- Grout placed discontinuously, leaving voids.
- Wrong mix, excessive shrinkage or high permeability.
- Hole collapse before grouting, mixing soil into the grout.
- No placement record or pressure check.
Sealing and pressure testing
Sealing isolates aquifers, especially where artesian water or contamination risk exists. Material, depth and records must meet the design and local rules. Closed loops are pressure tested before and after grouting to prove the pipe is sound.
Keep the pressure test, grouting record, borehole log and as-built drawing. They are the basis for diagnosing performance problems later.
Common problems and prevention
| Problem | Likely cause | Prevention |
|---|---|---|
| Loop will not reach bottom | Deviation, tight hole, fallen rock | Control deviation, ream before installation |
| Incomplete grout | Discontinuous placement, wrong mix | Tremie placement, record volumes |
| Poor heat transfer | Tight spacing, voids, groundwater flow | Follow layout, thermal response test |
| Loop leak | Scored pipe, poor joint | Inspect and pressure test |
| Hole collapse | Poor mud, long open time | Optimise mud, reduce open-hole time |
Rig selection
For shallow holes and scattered sites, a compact crawler or truck rig works. For deep holes, bedrock and difficult ground, choose sufficient head torque, mast height and cuttings capacity. Julong QY DTH water well rigs, JDL top-drive rigs and JY hydraulic core rigs cover different geothermal duties. Match the configuration to depth, diameter and ground.
A geothermal borehole is a long-term asset. Do not decide on cost per metre alone. Money saved on grouting and testing is usually paid back through system energy and repairs.
Frequently asked questions
How deep are ground-source heat pump boreholes?
There is no fixed depth. It depends on building load, ground thermal conductivity, groundwater and available land. A thermal response test and load calculation normally determine depth and number of holes.
Why is grouting important in a geothermal borehole?
Grout fills the annulus, improves heat transfer and blocks cross-flow between aquifers. Poor grouting reduces performance and can create groundwater problems.
What is the main difference from water well drilling?
A water well is designed to produce water. A geothermal borehole is designed for long-term heat exchange and sealing. Layout, loop installation, grouting, sealing and pressure testing are more demanding.